Power Options

Teledyne ISCO offers a variety of power options for its instruments, including batteries, power packs, and chargers.
Batteries
Nickel-Cadmium Batteries
Our nickel-cadmium battery is your best choice where a portable power source is needed in continuous-use applications. It allows more charging cycles than Lead-acid batteries and isn’t damaged by overcharging or being left totally discharged for extended periods.
- Maintenance Free
- Ruggedly Built
- Temperature tolerant

Model 934
| Output Voltage | 12-14 VDC |
| Amp/Hour Rating | 4.0 |
| Connector Type | 2-pin circular Amphenol |
| Recommended Use | Teledyne ISCO samplers, flowmeters, and portable pumps when used at regularly serviced monitoring sites. |
Lead-Acid Batteries
Teledyne ISCO’s lead-acid batteries are best used wherever portable standby power is required. They have a very low self-discharge rate and outperform nickel-cadmium batteries in applications where battery power is used sporadically over long periods of time. All of our lead-acid batteries are environmentally sealed and maintenance-free. Fluid level checks and refilling are not required.

Model 945

Model 946

Model 948
| Output Voltage | 6 VDC |
| Amp/Hour Rating | 5.0 |
| Connector Type | Coiled Wire |
| Output Voltage | 11-13.5 VDC |
| Amp/Hour Rating | 6.5 |
| Connector Type | 2-pin circular Amphenol |
| Output Voltage | 12 VDC |
| Amp/Hour Rating | 45 |
| Connector Type | 2-pin circular Amphenol |
| Recommended Use | Sites with intermittent or sporadic activity such as stormwater runoff monitoring, inflow and infiltration (I&I) studies, combined sewer overflow CSO monitoring, and more. |
Power Packs
High-capacity Power Packs
Our rugged, high capacity power packs safely and reliably convert available AC voltage to DC power.
- Built-in battery charger
- Environmentally sealed

Model 913

Model 923
| Input Voltage | 120 VAC 50 or 60 Hz |
| Output Voltage/Current | 12.5 VDC at 5 A |
| Connector Type | 2-pin circular Amphenol |
| Input Voltage | 240 VAC 50 or 60 Hz |
| Output Voltage/Current | 12.5 VDC at 5 A |
| Connector Type | 2-pin circular Amphenol |
| Recommended Use | Fixed installation or sites with reliable AC power. |
Battery-backed Power Packs
Teledyne ISCO’s battery-backed power packs assure that your equipment will keep running even if AC line voltage is interrupted.
- Battery backup
- Benchmark reliability

Model 914

Model 924
| Input Voltage | 120 VAC 50 or 60 Hz |
| Output Voltage/Current | 12-14.5 VDC 3 A continuous 5 A maximum |
| Connector Type | 2-pin circular Amphenol |
| Input Voltage | 240 VAC 50 or 60 Hz |
| Output Voltage/Current | 12-14.5 VDC 3 A continuous 5 A maximum |
| Connector Type | 2-pin circular Amphenol |
| Recommended Use | Fixed installations or sites with available AC power. This includes sites with an unreliable AC power supply. |
Chargers
Amphenol Connector Chargers
An Amphenol connector charger is a low-cost method for charging single Teledyne ISCO batteries. An impact-resistant case and solid-state construction make these chargers almost indestructible.

Model 961

Model 963

Model 965
| Input Voltage | 120 VAC at 60 Hz* |
| Output Voltage | 14.5 VDC at 400 mA* |
| Connector Type | 2-pin circular Amphenol |
| Input Voltage | 120 VAC at 60 Hz 240 VAC at 50 Hz |
| Output Voltage | 13.7 VDC at 720 mA |
| Connector Type | 2-pin circular Amphenol |
| Input Voltage | 120 VAC at 60 Hz 240 VAC at 50 Hz |
| Output Voltage | 13 VDC at 400 mA 14.9 VDC at 800 mA |
| Connector Type | 2-pin circular Amphenol |
| Recommended Use | *Charges up to five batteries simultaneously. **Contact factory for 240 VAC/50Hz input voltage. |
Clamp-on 12V Chargers
This charger constantly monitors 12 volt/6 Amp charge status, shuts down when charging is complete, and gives notification via LED.

12 Volt, 6 Amp*
| Input Voltage | 120 VAC at 60 Hz** |
| Output Voltage | 12 VDC at 6 A |
| Recommended Use | For use with Teledyne ISCO Model 948 or other 12-Volt lead-acid batteries. |
| | *Specifically compatible with Model 948 batteries. **Contact factory for 240 VAC/50Hz. |
Solar-powered Chargers
Teledyne ISCO’s solar-powered chargers deliver energy in long-term applications where AC power isn’t available. Units are selected from a variety of solar panel options to best suit your specific application. These chargers are recommended for remote or long-term installations at sites without available AC power.
Charger/battery Compatibility
| Nickel-Cadmium | Lead-Acid | ||||
|---|---|---|---|---|---|
| Model 934 | Model 945 | Model 946 | Model 947 | Model 948 | |
| Model 961 | |||||
| Model 963 | |||||
| Model 965 | |||||
| 12 Volt, 6 Amp | |||||
| Model 913 | |||||
| Model 923 | |||||
| Recommended. | |
| Requires Lantern Battery Charger Adapter. Contact Teledyne ISCO for details. | |
| Requires a connector. Contact Teledyne ISCO for details. |
Documentation
In-depth information can be found within the Power Products Brochure, the Power Products Guide, or by contacting Teledyne ISCO or an authorized Teledyne ISCO representative.
