MARKETS

From the office to the field, SITECH GULF offers a wide range of technology solutions to increase profitability, improve sustainability and enable rapid decision-making

Power Options

Teledyne ISCO offers a variety of power options for its instruments, including batteries, power packs, and chargers.

BROCHURE INSTALLATION OF OPERATION GUIDE

Batteries

Nickel-Cadmium Batteries

Our nickel-cadmium battery is your best choice where a portable power source is needed in continuous-use applications. It allows more charging cycles than Lead-acid batteries and isn’t damaged by overcharging or being left totally discharged for extended periods.

  • Maintenance Free
  • Ruggedly Built
  • Temperature tolerant
Model 934
Output Voltage ​12-14 VDC
​Amp/Hour Rating ​4.0
​Connector Type ​2-pin circular Amphenol
​Recommended Use ​Teledyne ISCO samplers, flowmeters, and portable pumps when used at regularly serviced monitoring sites.

Lead-Acid Batteries

Teledyne ISCO’s lead-acid batteries are best used wherever portable standby power is required. They have a very low self-discharge rate and outperform nickel-cadmium batteries in applications where battery power is used sporadically over long periods of time. All of our lead-acid batteries are environmentally sealed and maintenance-free. Fluid level checks and refilling are not required.

Model 945
Model 946
Model 948
Output Voltage 6 VDC
​Amp/Hour Rating ​5.0
​Connector Type Coiled Wire
Output Voltage 11-13.5 VDC
​Amp/Hour Rating ​​6.5
​Connector Type ​2-pin circular Amphenol
Output Voltage 12 VDC
​Amp/Hour Rating ​​45
​Connector Type 2-pin circular Amphenol
​​Recommended Use Sites with intermittent or sporadic activity such as stormwater runoff monitoring, inflow and infiltration (I&I) studies, combined sewer overflow CSO monitoring, and more. ​

Power Packs

High-capacity Power Packs

Our rugged, high capacity power packs safely and reliably convert available AC voltage to DC power.

  • Built-in battery charger
  • Environmentally sealed
Model 913
Model 923
​Input Voltage 120 VAC 50 or 60 Hz
Output Voltage/Current 12.5 VDC at 5 A
​Connector Type ​​2-pin circular Amphenol
​Input Voltage ​240 VAC 50 or 60 Hz
Output Voltage/Current 12.5 VDC at 5 A
​Connector Type ​​2-pin circular Amphenol
​​Recommended Use ​Fixed installation or sites with reliable AC power. ​
Battery-backed Power Packs

Teledyne ISCO’s battery-backed power packs assure that your equipment will keep running even if AC line voltage is interrupted.

  • Battery backup
  • Benchmark reliability
Model 914
Model 924
​Input Voltage 120 VAC 50 or 60 Hz
Output Voltage/Current 12-14.5 VDC 3 A continuous 5 A maximum
​Connector Type 2-pin circular Amphenol
​Input Voltage ​240 VAC 50 or 60 Hz
Output Voltage/Current 12-14.5 VDC 3 A continuous 5 A maximum
​Connector Type ​​2-pin circular Amphenol
​​Recommended Use ​ ​Fixed installations or sites with available AC power. This includes sites with an unreliable AC power supply. ​

Chargers

Amphenol Connector Chargers

An Amphenol connector charger is a low-cost method for charging single Teledyne ISCO batteries. An impact-resistant case and solid-state construction make these chargers almost indestructible.

Model 961
Model 963
Model 965
Input Voltage ​120 VAC at 60 Hz*
​Output Voltage 14.5 VDC at 400 mA*
​Connector Type 2-pin circular Amphenol
Input Voltage 120 VAC at 60 Hz 240 VAC at 50 Hz
​Output Voltage 13.7 VDC at 720 mA
​Connector Type ​​2-pin circular Amphenol
Input Voltage ​120 VAC at 60 Hz 240 VAC at 50 Hz
​Output Voltage 13 VDC at 400 mA 14.9 VDC at 800 mA
​Connector Type ​​2-pin circular Amphenol
​​Recommended Use *Charges up to five batteries simultaneously. **Contact factory for 240 VAC/50Hz input voltage.
Clamp-on 12V Chargers

This charger constantly monitors 12 volt/6 Amp charge status, shuts down when charging is complete, and gives notification via LED.

12 Volt, 6 Amp*
Input Voltage 120 VAC at 60 Hz**
​Output Voltage ​12 VDC at 6 A
Recommended Use ​For use with Teledyne ISCO Model 948 or other 12-Volt lead-acid batteries.
​​ *Specifically compatible with Model 948 batteries. **Contact factory for 240 VAC/50Hz.
Solar-powered Chargers

Teledyne ISCO’s solar-powered chargers deliver energy in long-term applications where AC power isn’t available. Units are selected from a variety of solar panel options to best suit your specific application. These chargers are recommended for remote or long-term installations at sites without available AC power.​

Charger/battery Compatibility

Nickel-Cadmium Lead-Acid
Model 934 Model 945 Model 946 Model 947 Model 948
Model 961
Model 963
Model 965
12 Volt, 6 Amp
Model 913
Model 923
Recommended.
Requires Lantern Battery Charger Adapter. Contact Teledyne ISCO for details.
Requires a connector. Contact Teledyne ISCO for details.

Documentation

In-depth information can be found within the Power Products Brochure, the Power Products Guide, or by contacting Teledyne ISCO or an authorized Teledyne ISCO representative.​

BROCHURE INSTALLATION OF OPERATION GUIDE

    REQUEST FOR QUOTATION